71M6533- DB Demo Board User’s Manual
2.5.4 HARDWARE WATCHDOG TIMER
The hardware watchdog timer of the 71M6533 is disabled when the voltage at the V1 pin is at 3.3V (V3P3). On
the Demo Boards, this is done by plugging in a jumper at TP10 between the V1 and V3P3 pins.
Programming the flash memory or emulation using the ADM51 In-Circuit-Emulator can only
be done when a jumper is plugged in at TP10 between V1 and V3P3.
Conversely, removing the jumper at TP10 will enable the hardware watchdog timer.
2.5.5 LCD
Various tests of the LCD interface can be performed with the Demo Board, using the serial command line
interface (CLI):
Setting the LCD_EN register to 1 enables the display outputs.
Register Name
LCD_EN
Address [bits]
2021[5]
R/W
R/W
Description
Enables the LCD display. When disabled, VLC2, VLC1, and
VLC0 are ground as are the COM and SEG outputs.
To access the LCD_EN register, we apply the following CLI commands:
>RI21$
>25
>RI21=5
>RI21=25
Reads the hex value of register 0x2021
Response from Demo Code indicating the bit 5 is set
Writes the hex value 0x05 to register 0x2021 causing the display to be switched off
Sets the LCD_EN register back to normal
The 71M6533 provides a charge pump capable of boosting the 3.3VDC supply voltage up to 5.0VDC. The
boost circuit is enabled with the LCD_BSTEN register. The 6533 Demo Boards have the boost circuit enabled by
default.
Register Name
LCD_BSTEN
Address [bits]
2020[7]
R/W
R/W
Description
Enables the LCD voltage boost circuit.
To disable the LCD voltage boost circuit, we apply the following CLI commands:
>RI20$
>8E
>RI20=E
>RI20=8E
Reads the hex value of register 0x2020
Response from Demo Code indicating the bit 7 is set
Writes the hex value 0x0E to register 0x2020 causing the LCD boost to be switched off
Enables the LCD boost circuit
The LCD_CLK register determines the frequency at which the COM pins change states. A slower clock means
lower power consumption, but if the clock is too slow, visible flicker can occur. The default clock frequency for
the 71M6533-DB Demo Boards is 150Hz ( LCD_CLK = 01).
Register Name
LCD_CLK[1:0]
Address [bits]
2021[1:0]
R/W
R/W
Description
Sets the LCD clock frequency, i.e. the frequency at which SEG
and COM pins change states.
f w = CKADC/128 = 38,400
00: f w /2 , 01: f w /2 , 10: f w /2 , 11: f w /2
9 8 7
To change the LCD clock frequency, we apply the following CLI commands:
6
>RI21$
>25
>RI21=24
Reads the hex value of register 0x2021
Response from Demo Code indicating the bit 0 is set and bit 1 is cleared.
Writes the hex value 0x24 to register 0x2021 clearing bit 0 – LCD flicker is visible now
Page: 52 of 75
`
REV 3
相关PDF资料
71M6534H-DB BOARD DEMO 71M6534H
71M6541F-DB DEMO BOARD 71M6541F
71M6543F-DB-CT DEMO BOARD 71M6543F-DB-CT
72-CNV-5 CONVERTER RS-232 TO RS-422 5V
72346-001 72346-1-SCA-II REC
72347-001LF CONN RECEPT SCA2 20POS VERT PCB
72436-001LF 80POS EXT HT. REC SCA-2
72442-201LF CONN RECEPT SCA2 80POS VERT PCB
相关代理商/技术参数
71M6533G 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Exceeds IEC 62053/ANSI C12.20 Standards
71M6533G-IGTR/F 功能描述:计量片上系统 - SoC AC Power Monitoring SoC-Programd RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6533H 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Energy Meter IC
71M6533H-IEL 制造商:Maxim Integrated Products 功能描述:Metering Systems on a Chip - SoC Precision Energy Meter IC
71M6533H-IEL/F 制造商:Maxim Integrated Products 功能描述:Metering Systems on a Chip - SoC Precision Energy Meter IC
71M6533H-IELR 制造商:Maxim Integrated Products 功能描述:Metering Systems on a Chip - SoC Precision Energy Meter IC
71M6533H-IELR/F 制造商:Maxim Integrated Products 功能描述:Metering Systems on a Chip - SoC Precision Energy Meter IC
71M6533H-IGT/F 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel